Garmin GT15M through-hull transducer for use with compatible Garmin fishfinders and chartplotters, providing CHIRP sonar capability for detailed underwater imaging.
Garmin thru-hull mounting hardware for GT-series transducers, providing the hardware needed for a clean, permanent through-hull transducer installation.
Garmin 12-pin transducer Y-cable for splitting a single transducer port to connect multiple compatible transducers to a Garmin fishfinder or chartplotter.
Connect a port/starboard pair of thru hull or transom mount transducers to the sonar unit with this 12-pin Y-cable. This cable allows the use of two different transducers to produce the left and ri...
Use our fairing block to position your GT56 series of thru-hull scanning transducers parallel to the water line for increased sonar accuracy. If the deadrise angle of your mounting location exceeds...
The AIRMAR® CM599LHW is a pocket mounted transducer that utilizes low and high frequencies to send depth and temperature to your Garmin Marine network.
Designed for coastal fishing with an operating frequency range of 150-250 kHz. This CHIRP transducer has a constant 25° beam width provides increased coverage under the boat. Designed for boats 25’...
This plastic thru-hull mount transducer uses the low frequencies for deep water performance and high wide frequencies for shallow water performance. A 2 kW in a slightly smaller package, this bare ...
The AIRMAR® B175HW (0° Tilt) has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175HW (0° Tilt) has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175HW (0° Tilt) has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
Designed for racing sailboats, the gWind Race features a 3.3 feet (1 meter) straight pole to raise the transducer above the mast to remove turbulence errors. It features twin-fin technology with 3-...
The gWind transducer features twin-fin technology with 3-bladed propeller for more accurate TWS in lighter air while the twin-fin design gives a more stable TWA. The 3-bladed propeller, unlike a cu...
Install your chartplotter in tight-fitting locations or replace your black box sonar cable with this 23.6 inch, right-angle transducer adapter cable. Supports all Garmin and Airmar (with XID) 12-pi...
Easily attach your compatible 4-, 8- or 12-pin transducer to the transom of your boat with this mount that provides excellent sonar returns at all speeds. Since the transducer is in the water at al...
The AIRMAR® B175M (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175M (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175M (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175L (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175L (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175L (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175H (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175H (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B175H (0° Tilt) transducer has a flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull & can sit on the trailer rollers/bunks.
The AIRMAR® B150M (20° Tilt) is a bronze thru-hull mount transducer that is an entry level CHIRP solution with good depth capability & target separation.
The AIRMAR® B150M (12° Tilt) is a bronze thru-hull mount transducer that is an entry level CHIRP solution with good depth capability & target separation.
